Dependable Kitchen Remodeling Plumbing in Buffalo Grove, IL
Kitchen plumbing for remodels can be a quick fix, like installing a new faucet or hooking up a disposal and dishwasher, or it can be a bigger job like relocating the sink to an island, running new gas lines for a stove, adding a prep sink, or roughing in a pot filler. The size of the job influences the cost, timeline, and whether permits are needed. We take care of every step.
Here’s my tip when you reach out at 224-455-8755: get your plumber involved before cabinets arrive. If the sink is moving, reconfiguring the drain and vent works best while the subfloor is open. Running a new gas line for a cooktop or range should happen before cabinet installation. Pot filler faucet setup means opening the wall behind the stove — much simpler before backsplash tiles go up. Scheduling us early saves headaches and delays.
We also handle stand-alone kitchen plumbing jobs without remodels — faucet swaps, disposal repairs and installs, dishwasher hookups, and refrigerator water lines. Remodeling is a great time to check your water heater capacity and clear any slow kitchen drains before new cabinetry covers them up. Call 224-455-8755 if you need help with any of these.
Our Kitchen Plumbing Services
Sink and Faucet Installations
We work with all common kitchen sink styles — undermount sinks that require careful countertop cutouts, drop-in models, farmhouse/apron front, one- or two-bowl sinks, and prep sinks. We handle installing drain strainers, P-traps, and braided stainless supply lines—not the brittle plastic ones that fail over time. We also attach garbage disposals during the same visit when needed.
For faucets, we install every setup: single-hole, three-hole, or deck-plate mountings. We pressure-test everything before we wrap up. Moving sinks to a new spot requires rerouting drains, vent pipes, and supply lines with proper permits, and we’re fully equipped to tackle those larger projects.
Hooking Up Dishwashers & Appliances
Dishwasher connections include hot water supply, drain hose with a required high loop or air gap to prevent backflow, plus checking electrical readiness (though that’s an electrician’s job, we coordinate). For refrigerators, we run dedicated cold water lines for ice makers or water dispensers using copper or braided stainless steel, making sure there’s a shutoff behind the fridge.
We also install instant hot water taps, under-sink water filters, and reverse osmosis systems. For RO, we fit a dedicated faucet through the sink deck, connect supply and drain lines, and give you advice on maintenance. Call 224-455-8755 to handle any appliance plumbing needs.
Gas Line Installation for Kitchen Appliances
Thinking about switching from electric to gas, or adding a gas cooktop on an island? We handle gas line installations from start to finish — sizing pipes based on BTUs, running line from your gas supply, installing shutoffs, connecting appliances with flexible connectors approved by code, pressure testing, and securing permits and inspections. Visit our gas line services page for details on safety and process.
Important: new gas lines to islands or relocated appliances must be roughed in before cabinetry goes in. Running gas lines afterward is a headache and more invasive. Coordinate early with your GC and us.
Pot Filler Faucet Setup
A pot filler faucet sits above your stove so you can fill pots without carrying them across the kitchen. It needs a cold water line run inside the wall about 56 to 60 inches from the floor and a few inches off center of the range. This is easiest during remodels when walls are open; installing in finished kitchens requires cutting and patching walls and surfaces, but we manage that too. Call 224-455-8755 to explore options.
Island Sink Drain and Vent Installation
Installing a sink on an island is tricky because drains can’t tie into wall vents the usual way. Island sinks need either an island loop vent or an air admittance valve (AAV), depending on Buffalo Grove’s plumbing codes. Running hot and cold supply lines to the island is straightforward, but routing drain and vent pipes under the floor and inside the cabinet requires detailed planning. We’ve handled many island sink installs and can advise you before finalizing your kitchen design.
Kitchen Plumbing Checklist
- Removal and installation of kitchen sinks (undermount, farmhouse, drop-in)
- Faucet installation for all styles
- Garbage disposal installs or replacements
- Dishwasher water supply and drain setup
- Water line installation for refrigerator ice makers
- Gas line installation for ranges, cooktops, or ovens
- Pot filler faucet rough-in and final installation
- Under-sink filtration and reverse osmosis system installs
- Drain and vent routing for island sinks
- Shutoff valve upgrades throughout kitchen plumbing
- Installation of prep or bar sinks in pantries or islands
Timing Tips for Kitchen Plumbing
- Confirm sink location before demo: Moving a sink is the most expensive plumbing change — finalize placement before ordering cabinets
- Complete gas line rough-in early: New gas runs for islands or relocated appliances must be done before cabinets are installed
- Install pot filler before backsplashes: Wall opening is much easier before tile work begins
- Upgrade shutoff valves while plumbing is exposed: Replace old gate valves with reliable ball valves during remodel
- Run refrigerator water line before countertops: Easier to install ice maker lines before counters are set
Kitchen Remodeling Questions Answered
Yes, but it’s the most involved kitchen plumbing change. Island sinks need special venting like an island loop vent or an air admittance valve. Supply lines are straightforward, but the drain routing under the floor requires careful work. We’ve done many island sink installs—call 224-455-8755 to talk through your layout before you finalize plans.
For simple fixture replacements like faucets or disposals in the same spot, permits usually aren’t needed. But for moving drains, rerouting supply lines, adding gas lines, or altering plumbing layouts, permits are necessary. We take care of obtaining permits and scheduling inspections for you.
Yes, and it’s best done during remodeling when walls are open. We install gas lines for ranges, cooktops, and ovens with proper sizing, pressure testing, and permits. Make sure to plan the gas rough-in before the cabinets go in.
Definitely. We serve as plumbing subcontractors on kitchen remodels, syncing our scheduling and permits with your GC or designer. Call 224-455-8755 early to get us involved in your project’s timeline.